RAID upgrade

For my home server, I have filesystems on LVMs on RAIDs on partitions. Upgrading a disk is then, arguably, rather non-trivial. However the intended benefit of this setup is, hopefully, that I can roll over the oldest disk in the array every year or so, and so the whole lot grows incrementally as needed. "live" expansion on all levels means I should never have to create a new filesystem and copy data over, as per historic efforts.

These are my notes-to-self as of the time leading up to my first hardware change. Prior to this all disks are identical in size. There will be no significant size benefit until the fourth disk (smallest) is upgraded. After that, every upgrade (of the smallest disk - presumably replacing it to become the new 'largest') will yield a size increase - based upon the limits set by the 'new' smallest (oldest) disk.

This is not optimal use of available disk space for any given drive over it's life. However, it is hopefully rather nice in terms of budgetry upgrade requirements! :)

Pros

• Rolling upgrades are win.
  • response: rolling upgrades are the planning headache

Cons

• Each drive increase size is predicated on the drive purchased 3 drives back! So 'instant embiggening' is difficult.
  • response: you don't use this system unless you plan to think ahead anyway. Also, the old drive being taken out could be put into external USB caddy for additional space
  • response two: the 'unused' space on each drive (ie, the size difference between it and the smallest/oldest) could be partitioned into non-raid usable emergency spaces too!

My system

Software

# cat /etc/debian_version 
lenny/sid
# uname -a
Linux falcon 2.6.18-6-amd64 #1 SMP Mon Jun 16 22:30:01 UTC 2008 x86_64 GNU/Linux
# mdadm --version
mdadm - v2.5.6 - 9 November 2006
# lvm version
  LVM version:     2.02.07 (2006-07-17)
  Library version: 1.02.08 (2006-07-17)
  Driver version:  4.7.0

Setup

# cat /proc/mdstat
Personalities : [raid1] [raid6] [raid5] [raid4]
md3 : active raid5 sda4[0] sdd4[3] sdc4[2] sdb4[1]
      2637302400 blocks level 5, 64k chunk, algorithm 2 [4/4] [UUUU]

md2 : active raid1 sdc3[0] sdd3[1]
      87891520 blocks [2/2] [UU]

md0 : active raid1 sda2[0] sdb2[2](S) sdd2[3](S) sdc2[1]
      8787456 blocks [2/2] [UU]

md1 : active raid1 sda3[0] sdb3[1]
      87891520 blocks [2/2] [UU]

unused devices: <none>

# pvs
  PV         VG            Fmt  Attr PSize  PFree 
  /dev/md1   volgrp_home   lvm2 a-   83.82G     0 
  /dev/md2   volgrp_home   lvm2 a-   83.82G 27.63G
  /dev/md3   volgrp_shared lvm2 a-    2.46T     0 

# vgs
  VG            #PV #LV #SN Attr   VSize   VFree 
  volgrp_home     2   1   0 wz--n- 167.63G 27.63G
  volgrp_shared   1   1   0 wz--n-   2.46T     0

# lvs
  LV        VG            Attr   LSize   Origin Snap%  Move Log Copy% 
  lv_home   volgrp_home   -wi-ao 140.00G
  lv_shared volgrp_shared -wi-ao   2.46T

The plan

Upgrading each disc in turn to a larger physical disc... (1.5TB or 2TB, etc), all levels can be grown and expanded...

I'll start with /dev/sda, initially making partitions 1,2,3 the same, and partition 4 (for md3 - /shared) larger. md3 will only be able to expand once ALL FOUR discs are enlarged!

...note: I may enlarge md1 and md2 for larger /home as well...

So - like this

1. within mdadm
   1. Remove sda2 from within the md0 raid1 - this array has 2 spares)
   2. Remove sda3 from within the md1 raid1 - this has NO SPARE)
   3. Remove sda4 from within the md3 raid5)
2. Hardware setup
   1. Replace drive physically
   2. Partition
3. in mdadm again
   1. join sda1, sda2, sda3 and sda4 into their respective MD devices
4. within LVM
   1. enlarge the respective VG and LVs in turn
5. Finally, enlarge the filesystem.

Implemented

Removing partition from a raid1 with spares

# mdadm --fail /dev/md0 /dev/sda2
# mdadm --remove /dev/md0 /dev/sda2

You can watch a spare take over with

# cat /proc/mdstat

This process starts immediately after the --fail. No, you don't get to choose which spare will be used. There is an internal order (mdstats shows it inside [] brackets). In my case, I was using a and c. When I failed a, it spared to b. Yet I plan for 'b' to be the next drive out, and so it'll spare over to d later and I'll have c and d running! (with a and b as newer drives as spares, so I think that works out sensibly :)

Finally, I can now add that drive back as the oldest spare... just for kicks till it needs to be pulled physically...

# mdadm  --add /dev/md0 /dev/sda2

TODO

Removing partition from a raid1 without spares

This should be the same as the raid1 with spares, except that it'll remain a degraded raid until the new drive goes in and it's repaired.

Removing partition from a raid5 without spares

Same again. Fail a drive, and repair when the new drive is in?

Adding new partitions to existing raid1 and raid5 devices

this is an mdadm command. Something like --build or --repair or similar. Tired now. read doco later.

Embiggening volume groups

Some magical vg command? vgextend?

Embiggening logical volumes

Some magical lv commands? lvextend?

Embiggening ext3 filesystem

Some magical resize2fs command?

External reference

• http://ubuntuforums.org/showthread.php?t=1308597
• http://tldp.org/HOWTO/LVM-HOWTO/commontask.html
  • http://tldp.org/HOWTO/LVM-HOWTO/extendlv.html